Wireless Winch Remote Control Twin Handset Winchmax 12 Volt + Lead + Socket

WIRELESS WINCH REMOTE CONTROL TWIN HANDSET WINCHMAX 12 VOLT + LEAD + SOCKET. Premium winches & auto accessories.

The original orange pulling machine. SAME DAY DISPATCH ON ORDERS RECEIVED BEFORE 2PM. SEE WINCHMAX WEBSITE FOR DETAILS.

UK based supply and service. Latest WINCHMAX combo remote system kit. Improved components, Improved reliability, Improved range, Improved battery life. This is a new and innovative design which combines the mm precision control of a manual wander lead system with the convenience of a wireless system. It uses a robust handheld controller which can be plugged into the control box in the usual way but the clever bit is that if you disconnect the cable, with the press of a button the handheld controller becomes fully wireless allowing you to control the winch from a distance of up to 100ft away.

This kit is supplied with TWO handled combo controllers (so you have a backup if one gets lost or damaged), a receiver, plug in wander lead & wander lead socket. Everything you need to upgrade your existing winch to the latest combo wireless remote system. Suitable for 12V winches up to 18000lb. Latest heavy duty long range model by Winchmax BEWARE OF CHEAP COPIES!

Free- Fitted Battery in remote! Heat shielded cables with pre-fitted heat shrink insulated terminals for easy fitting. This listing is for a 12V model. We have tried almost every remote system available and can confidently say that these are the best solution on the market. Once you have used a wireless remote you will never want to be without one again, an absolute must have for any recovery or off roading operations.

You can operate the winch from a safe distance and when recovering vehicles, you can steer them while operating the winch from inside at the same time. No need to stand out in the rain! Each remote is uniquely coded to the transmitter to ensure there is no possibility of interference from other transmitters. The receiver is just 60mm x 45mm x 22mm and can be placed inside your existing solenoid enclosure.

It is very simple to install in just a few minutes. The cables are colour coded (see below).

The receiver fits neatly inside the solenoid pack. It is fitted with lugs to slide into the fitting rails found inside many solenoid boxes.

If there are no rails in your box just use double sided foam adhesive pads. This should provide many years of trouble free operation, however it is essential that it is correctly installed otherwise irreparable damage to the micro circuitry will be caused. The basic principle of operation is that once connected to a power supply, the two output wires of the receiver will go to the supply voltage (12v or 24v depending on the model) when the corresponding button on the transmitter (hand set) is pressed.

The output can then be used to operate the trigger terminals on a secondary contactor (solenoid) to switch the main load e. The outputs MUST NEVER be connected to earth as otherwise they will short circuit and burn out. If you have any doubt about which are the trigger terminals on your solenoid, first check by using a thin piece of wire connected to the positive supply, when you apply it to one of the solenoid trigger terminals the winch should run in one direction, if you apply it to the trigger terminal it should operate in the opposite direction.

In most cases winches are fitted with a plug in wander lead, at the back of the wander lead socket you will see three wires. One of the wires is the positive feed to the wander lead switch, depending on which way the switch is pressed this feed will then be diverted down one of the other two wires (the output wires) which will in turn be connected to the trigger terminal of the solenoid. There are many different types of control configurations, but if you understand the basic principle of operation this should allow you to apply it to whichever set you have. We have provided a schematic of the most common single solenoid pack winch control system (in our diagram trigger terminals on the solenoid are labelled as 1 & 3) but if you have any doubt as to how you should connect your remote DO NOT do it before consulting our office hours helpline for advice. (see contact details link at bottom of listing).

WINCH WIRELESS REMOTE CONTROL TWIN HANDSET 12V 12 VOLT EXTERNAL MOUNT RECEIVER. WINCHMAX 12v Wireless Remote Control Twin Handset.

WIRELESS WINCH REMOTE CONTROL TWIN HANDSET WINCHMAX BRAND 12V 12 VOLT. Here at the Winch Shop we are all dedicated winch enthusiasts. Our aim to bring you top quality products at reasonable prices.

We work very hard to make sure we deliver customer service above and beyond industry standards. The item "WIRELESS WINCH REMOTE CONTROL TWIN HANDSET WINCHMAX 12 VOLT + LEAD + SOCKET" is in sale since Monday, August 1, 2016. This item is in the category "Vehicle Parts & Accessories\Other Vehicle Parts & Accs". The seller is "integratas" and is located in Norfolk. This item can be shipped worldwide.

Manufacturer Part Number: WMSLREMKIT12VT
Brand: Winchmax